Manual de servicio

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) Owners Installation Manual. Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire.

Download: 1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) Owners Installation Manual

2007 Acura RDX Navigation Owners Manual, Manual Overview The 2007 Acura RDX Navigation Owners Manual is divided into the following sections: Your navigation system is a highly sophisticated location system with voice control that uses satellites and a map database to show you where you are and to help guide you to a desired destination.• Getting started – A basic introduction that discusses the controls and how to communicate with the system. • Entering a Destination – How to enter an address or locate a point of interest (POI). • Driving to your Destination – An explanation of the map features, guidance, and cautions. • Information Features – Message, Voice Command Help, Trip Computer, Map Legend, Calendar, Key to Zagat Ratings, Calculator, and Roadside Assistance. • System Set-up – How to set up and tailor the system for your personal use and use the Address Book The navigation system receives signals from the global positioning system (GPS), a network of 24 satellites in orbit around the earth. By receiving signals from several of these satellites, the navigation system can determine the latitude, longitude, and elevation of your vehicle. In addition, a gyroscopic yaw sensor and a vehicle speed sensor in your vehicle keep track of the direction and speed of travel at all times. The navigation system applies this location, direction, and speed information to the maps and calculates a route to the destination you enter. As you drive to that destination, the system provides map and voice guidance. The navigation system is easy to use. The locations of many places of business and entertainment are already entered in the system. You can select any of them as a destination by using the Interface Dial or voice control. There are several ways thttp://www.blogger.com/img/blank.gifo enter a destination, such as by point of interest (POI), by address, by phone number, and by selecting it from the map. Thel ast 50 destinations are saved for reuse at a later date. The system also allows you to store a home address to simplify returning home from your destination,


Download: 2007 Acura RDX Navigation Owners Manual

Be certain the gasket-mating surface on the intake manifold is clean and free of debris. Using the factory nuts and bolts and the new gasket supplied in the kit, attach the throttle body to the intake manifold. Torque nuts and bolts down to 20 N·m or 14 lbf·/ft. 10. Slip the throttle cable on the linkage arm. 11. Observe the throttle body while an assistant presses and releases the gas pedal to ensure that the throttle blade opens and closes completely as well as smoothly. 12. Re-atthttp://www.blogger.com/img/blank.gifach the air filter duct, all vacuum hoses, coolant hoses and electrical connectors on the new throttle body. 13. Re-connect the negative battery terminal. 14. Start the engine and check for loose connections or coolant/vacuum leaks, etc. 15. After the engine is warmed up, check the idle speed (refer to owners manual). 16. Double-check all fasteners, clamps, and electrical connections to ensure they are all secure.This Edelbrock part has received and Executive Order number (E.O. #) from the California Air Resource Board (C.A.R.B.) making it legal for street use on pollution-controlled motor vehicles in all 50 states. To assist you with emissions equipment certification, we have included a silver E.O. Number decal to help testing personnel verify that this part is a legal replacement part on the vehicle for which it is cataloged. The adhesive-backed decal should be affixed to your hood underside next to the existing emission and engine specification decal. Do not cover your original equipment specification decal with the Edelbrock E.O. Number decal.

Download: Acura Integra GSR VTEC Throttle Body INSTALLATION INSTRUCTIONS

2004+ Acura TSX Installation Instructions. The most common cause of brake vibration is improper bed-in of pads and rotors, or improper pad selection for the specific driving environment. Rotor run-out may also cause vibration, but precision manufacturing and inspection typically mean that run-out is not an issue. Modern production methods ensure that the rotor run-out is within +/- 0.002″ when installed on a StopTech aluminum hat, and it controls thickness variation to within 0.0003″. Under the most extreme conditions, any rotor may warp, but uneven pad deposition is a more typical cause of vibration. If the system is not properly bedded-in, or if street pads are run on an open track, uneven pad deposits will occur, causing an ever-worsening vibration. Failure to immediately address a pad deposition/vibration issue may lead to permanent damage of the rotors. Please read and understand the bed-in procedure. All photographs show a left-hand side installation, unless otherwise noted. side installation, unless otherwise noted. side installation, unless otherwise noted. side installation, unless otherwise noted. side installation, unless otherwise noted. Some components shown in this installation Some components shown in this installation Some components shown in this installation Some components shown in this installation Some components shown in this installation manual are prototype parts which have not manual are prototype parts which have not manual are prototype parts which have not manual are prototype parts which have not manual are prototype parts which have not be anodized. The actual components in your be anodized. The actual components in your be anodized. The actual components in your be anodized. The actual components in your be anodized. The actual components in your kit may appear visually different from those kit may appear visually different from those kit may appear http://www.blogger.com/img/blank.gifvisually different from those kit may appear visually different from those kit may appear visually different from those shown in the manual, but all of the instal- shown in the manual, but all of the instal- shown in the manual, but all of the instal- shown in the manual, but all of the instal- shown in the manual, but all of the installation

Download: Installation Instructions Acura TSX 2004+

2007 Acura TL Owners Manual. This Owners Manual Contain. Index I Service Information Summary last page Your Vehicle at a Glance 3 Driver and Passenger Safety 5 Instruments and Controls 55 Features 125 Before Driving 233 Driving 245 Maintenance 271 Taking Care of the Unexpected 311 Technical Information 335 Warranty and Customer Relations (U.S. and Canada only) 351 Authorized Manuals (U.S. only) 355. river and Passenger Safety Important Safety Precautions 6 Your Vehicle’s Safety Features 7 Protecting Adults and Teens 11 1. Close and Lock the Doors 11 2. Adjust the Front Seats 12 3. Adjust the Seat-Backs 13 4. Adjust the Head Restraints 13 5. Fasten and Position the Seat Belts 14. Maintain a Proper Sitting Position 16Advice for Pregnant Women 16Additional Safety Precautions 17Additional Information About Your Seat Belts 18Seat Belt System Components 18Lap/Shoulder Belt 19Automatic Seat Belt Tensioners 20Seat Belt Maintenance 21Additional Information About Your Airbags 22 Airbag System Components 22.


Download: 2007 Acura TL Owners Manual

1994 – 1997 Honda Acura Integra Service Manual. i have fohttp://www.blogger.com/img/blank.gifund Honda Acura Integra 1994 – 1997 Service Manual that you are looking for, click the link below to download. Integra, sold as an Acura in North America, and as a Honda elsewhere, was a small, sporty front-wheel drive vehicle sold both as a sedan and hatchback.Total Car Care is the most complete, step-by-step automotive repair manual you’ll ever use. All repair procedures are supported by detailed specifications, exploded views, and photographs. From the simplest repair procedure to the most complex, trust Chilton’s Total Car Care to give you everything you need to do the job. Save time and money by doing it yourself, with the confidence only a Chilton Repair Manual can provide.

Download: 1994 – 1997 Honda Acura Integra Service Manual