Manual de servicio

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) Owners Installation Manual. Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire.

Download: 1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) Owners Installation Manual

APPLE BOOT CAMP INSTALLATION AND SETUP MANUAL GUIDE FOR MACBOOK AIR 2010. Boot Camp lets you install Windows on a Mac computer in its own partition, using a Microsoft Windows installation disc that you provide. After installation, you can use either Windows or Mac OS X on your Mac computer. The Boot Camp Assistant application and this guide walk you through the steps needed to create a Windows partition on your Mac and then restart your Mac using your Windows installation disc. Then, follow this guide to install Windows and install software drivers that let Windows work with your Mac hardware.Boot Camp Assistant helps prepare your Mac for Windows by downloading Windows support software, creating a new partition for Windows, and then starting the Windows installer. Make sure you have a blank CD or DVD or an external drive formatted as MS-DOS (FAT) where Boot Camp Assistant can save the Windows support software, which you’ll later install on your Windows partition. To format an external drive as MS-DOS (FAT), use Disk Utility in the Utilities folder in the Applications folder.Read and carefully follow these instructions for installing Windows on your Mac computer. Refer to your Windows documentation for general information about installing and setting up Windows. If you already quit Boot Camp Assistant without installing Windows, open Boot Camp Assistant and continue from where you left off.


Download: APPLE BOOT CAMP INSTALLATION AND SETUP MANUAL GUIDE FOR MACBOOK AIR 2010

N60 ENT M37 MARINE ENGINE INSTALLATION INSTRUCTIONS. Please read carefully the indications provided in this document compliance with them will ensure the engine will continue to run smoothly and reliably, protecting users and service personnel against the risk of mishaps. The instructions contained in this document pertain specifically to the N60 ENT M37 engine and complement the IVECO Aifo publication “Marine Engine Installation Manual”, which should be referred to for all matters not covered herein. Any installation not in compliance with the contents of these instructions, or modifications to the engine and its fittings are not admitted.The installing Yard is required to conduct tests to verify the functional compatibility between the engine’s electrical-electronic equipment and the other electronic devices present on the boat. Engineers and installation personnel are reminded of their obligation to comply with workplace safety rules. To ready the engine for starting, follow the procedure set out at the end of Section 2 of this document. To get the best possible performance out of the engine, it is mandatory to conform with its intended mission profile.The engine must not be used for purposes other than those stated by the manufacturer. IVECO Aifo is willing to examine beforehand any requirements for particular installations. The purpose of the commercial code is to make it easier to understand the characteristics of the product, categorizing the engines according to their family, origins and intended application.The commercial code, therefore, cannot be used for technical purposes to recognize the engine’s components, this purpose is served by the “ENGINE S/N”.

Download: N60 ENT M37 MARINE ENGINE INSTALLATION INSTRUCTIONS

Be certain the gasket-mating surface on the intake manifold is clean and free of debris. Using the factory nuts and bolts and the new gasket supplied in the kit, attach the throttle body to the intake manifold. Torque nuts and bolts down to 20 N·m or 14 lbf·/ft. 10. Slip the throttle cable on the linkage arm. 11. Observe the throttle body while an assistant presses and releases the gas pedal to ensure that the throttle blade opens and closes completely as well as smoothly. 12. Re-atthttp://www.blogger.com/img/blank.gifach the air filter duct, all vacuum hoses, coolant hoses and electrical connectors on the new throttle body. 13. Re-connect the negative battery terminal. 14. Start the engine and check for loose connections or coolant/vacuum leaks, etc. 15. After the engine is warmed up, check the idle speed (refer to owners manual). 16. Double-check all fasteners, clamps, and electrical connections to ensure they are all secure.This Edelbrock part has received and Executive Order number (E.O. #) from the California Air Resource Board (C.A.R.B.) making it legal for street use on pollution-controlled motor vehicles in all 50 states. To assist you with emissions equipment certification, we have included a silver E.O. Number decal to help testing personnel verify that this part is a legal replacement part on the vehicle for which it is cataloged. The adhesive-backed decal should be affixed to your hood underside next to the existing emission and engine specification decal. Do not cover your original equipment specification decal with the Edelbrock E.O. Number decal.

Download: Acura Integra GSR VTEC Throttle Body INSTALLATION INSTRUCTIONS

2004+ Acura TSX Installation Instructions. The most common cause of brake vibration is improper bed-in of pads and rotors, or improper pad selection for the specific driving environment. Rotor run-out may also cause vibration, but precision manufacturing and inspection typically mean that run-out is not an issue. Modern production methods ensure that the rotor run-out is within +/- 0.002″ when installed on a StopTech aluminum hat, and it controls thickness variation to within 0.0003″. Under the most extreme conditions, any rotor may warp, but uneven pad deposition is a more typical cause of vibration. If the system is not properly bedded-in, or if street pads are run on an open track, uneven pad deposits will occur, causing an ever-worsening vibration. Failure to immediately address a pad deposition/vibration issue may lead to permanent damage of the rotors. Please read and understand the bed-in procedure. All photographs show a left-hand side installation, unless otherwise noted. side installation, unless otherwise noted. side installation, unless otherwise noted. side installation, unless otherwise noted. side installation, unless otherwise noted. Some components shown in this installation Some components shown in this installation Some components shown in this installation Some components shown in this installation Some components shown in this installation manual are prototype parts which have not manual are prototype parts which have not manual are prototype parts which have not manual are prototype parts which have not manual are prototype parts which have not be anodized. The actual components in your be anodized. The actual components in your be anodized. The actual components in your be anodized. The actual components in your be anodized. The actual components in your kit may appear visually different from those kit may appear visually different from those kit may appear http://www.blogger.com/img/blank.gifvisually different from those kit may appear visually different from those kit may appear visually different from those shown in the manual, but all of the instal- shown in the manual, but all of the instal- shown in the manual, but all of the instal- shown in the manual, but all of the instal- shown in the manual, but all of the installation

Download: Installation Instructions Acura TSX 2004+

Honda ACCORD 2002 Timing Belt and Balancer Belt Installation Service Repair Manual. Align the dimple (A) on the tooth of the timing belt drive pulley with the pointer (B) on the oil pump. 4. Honda ACCORD 2002 Clean the camshaft pulley and set it to TDC. 5. Install the timing belt in a counterclockwise sequence, starting with the drive pulley. -1 The ”UP” mark (A) on the camshaft pulley should be at the top. -2 Align the TDC grooves (B) on the pulley with the top edge of the head. -1 Drive pulley (A). -2 Tensioner pulley (B). -3 Water pump pulley (C). -4 Camshaft pulley (D). 6. Loosen and retighten the adjusting nut to tension the timing belt. 7. Clean any oil off both faces of the balancer belt drive pulley. 8. Check the lower cover rubber seal for cracks and other damage. NOTE: ?If the rubber seal is coming off, apply liquid gasket to the lower cover and reinstall the rubber seal. Wipe off any liquid gasket that is pressed out. ?When replacing the rubber seal, clean the lower cover groove, cut the repair rubber seal to length, and put the rubber seal into the groove evenly. 9. Install the balancer belt drive pulley and the lower cover. 10. Temporarly install the crankshaft pulley and bolt. 11. Rotate the crankshaft pulley five or six turns counterclockwise to seat the timing belt on the pulleys. 14. Check the camshaft pulley marks. ?If the camshaft pulley marks are also at TDC, go to step 15. ?If the camshaft pulley marks are not at TDC, remove the timing belt and repeat steps 3, 4 and 5. 15. Remove the crankshaft pulley and the lower cover.

Download:Honda ACCORD 2002 Timing Belt and Balancer Belt Installation Service Repair Manual

2004-2006 DODGE RAM 2500/3500 2 & 4WD DIESEL ENG 3″ BODY LIFT INSTALLATION INSTRUCTIONS. Installation of a Performance Automotive Group body lift kit will change the vehicle’s center of gravity and handling characteristics both on- and off-road. You must drive the vehicle safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fas- tened.Proper installation of this kit requires knowledge of the factory recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle. We strongly recommend that a certified mechanic familiar with the installation of similar components install this kit.Accidental deployment of the air bag can result in serious personal injury or death. To avoid accidental deployment during installation of the kit, the Supplemental Restraint System (SRS, or airbag) must remain deactivated. Do not allow anyone near the airbag during installation. Refer to the factory service manual or owner’s manual for the recommended procedure to disable the SRS. After you install the kit, reactivate the SRS before driving the vehicle.

Download: 2004-2006 DODGE RAM 2500/3500 2 & 4WD DIESEL ENG 3″ BODY LIFT INSTALLATION INSTRUCTIONS

2005 Suzuki Aerio Installation Instructions. Confirm the towability and pre-towing procedures for your vehicle with the owner’s manual or contact the vehicle’s manufacturer for specifi c towing procedures.Many Blue Ox® Baseplates are designed to use existing holes and hardware to mount the baseplate to the towed vehicle. Even though bolts are there, do not assume they are adequate for baseplate mounting. Always use hardware supplied in the hardware kit and existing hardware specifi ed in the Baseplate Installation Instructions.The front fascia, air intake tube and windshield washer reservoir are removed for baseplate installation. Drilling is required. Trimming of the air dam behind the bumper on passenger’s side is required. The dimensional variations between otherwise identical vehicles can be considerable. While the baseplate was designed for easy installation, it may be necessary to tailor the baseplate slightly to compensate for auto manufacturer’s tolerances. These minor adjustments may include fi ling a hole slightly, bending electrical rods or bending end plates. The Bx8869 Bulb and Socket Wiring Kit is recommended for this vehicle.

Download: 2005 Suzuki Aerio Installation Instructions Owners manual